Tag Archives: single-page apps

Adobe Launch’s Rule Ordering is a big deal for Single Page Apps

In November, I posted about some of the ways that Launch will make it easier to implement on Single Page Apps (SPAs), but I hinted that a few things were still lacking.
In mid-January, the Launch team announced a feature I’ve been eagerly awaiting: the ability to order your rules. With this ability, we finally have a clean and easy way to implement Adobe Analytics on a Single Page App.

The historical problem

As I mentioned in my previous post, one of the key problems we’ve seen in the past was that Event-Based Rules (EBRs) and Direct Call Rules (DCRs) can’t “stack”. Let me explain what I mean by that.

Not a single page app? Rule Stacking rocks!

For example, let’s say I have an internal search “null results” page, where the beacon that fires should include:

  • Global Variables, like “s.server should always be set to document.hostname”
  • Variables specific to the e-commerce/product side of my site with a common data layer structure (pageName should always be set to %Content ID: Page Name%)
  • Search Results variables (like my props/eVars for Search Term and Number of Search Results, and a custom event for Internal Searches)
  • Search Results when a filter is applied (like a listVar for Filter Applied and an event for User applied Search Filter)
  • Null Results Variables (another event for Null Internal Searches and a bit of logic to rewrite my Number of Search Results variable from “0” to “zero” (because searching in the reports for “0” would show me 10, 20, 30… whereas “zero” could easily show me my null results)

With a non-SPA, when a new page load loads, DTM would run through all of my page load rules and see which had conditions that were matched by the current page. It would then set the variables from those rules, then AFTER all the rules were checked and variables were set, DTM would send the beacon, happily combining variables from potentially many rules.

Would become this beacon:

If you have a Page Load Rule-based implementation, this allows you to define your rules by their scope, and can really use the power of DTM to only apply code/logic when needed.

Single Page App? Not so much.

However, if I were in a Single Page App, I’d either be using a Direct Call Rule or an Event-Based Rule to determine a new page was viewed and fire a beacon. DCRs and EBRs have a 1:1 ratio with beacons fired- if a rule’s conditions were met, it would fire a beacon. So I would need to figure out a way to have my global variables fire on every beacon, and set site-section-specific and user-action-specific variables, for every user action tracked. This would either mean having a lot of DCRs and EBRs for all the possible combos of variables (meaning a lot of repeat effort in setting rules, and repeated code weight in the DTM library), or a single massive rule with a lot of custom code to figure out which user-action-specific variables to set:

Or leaving the Adobe Analytics tool interface altogether, and doing odd things in Third Party Tag blocks. I’ve seen it done, and it makes sad pandas sad.

The Answer: Launch

Launch does two important things that solve this:

  1. Rules that set Adobe Analytics Variables do not necessarily have to fire a beacon. I can tell my rule to just set variables, to fire a beacon, or to clear variables, or any combination of those options.
  2. I can now order my rules to be sure that the rule that fires my beacon goes AFTER all the rules that set my variables.

So I set up my 5 rules, same as before. All of my rules have differing conditions, and use two similar triggers: one set to fire on Page Bottom (if the user just navigated to my site or refreshes a page, loading a fresh new DOM) and one on Data Element Changed (for Single Page App “virtual page views”, looking at when the Page Name is updated in the Data Layer).

When I create those triggers, I can assign a number for that trigger’s Order:


One rule, my global rule, has those triggers set to fire at “50” (which is the default number, right in the middle of the range it is recommended that I use, 1-100). The rule with this trigger not only sets my global variables, it also fires my beacon then clears my variables:

Most of my other rules, I give an Order number of “25” (again, fairly arbitrary, but it gives me flexibility to have other rules fire before or after as needed). One rule, my “Internal Search: Null Results” rule is set to the Order number “30”, because I want it to come AFTER the “Internal Search: Search Results” rule, since it needs to overwrite my Number of Search Results variable from “0” (which it got from the data layer) to “Zero”.

This gives me a chance to set all the variables in my custom rules, and have my beacon and clearVars fire at the end in my global rule (the rule’s Order number is in the black circles):

I of course will need to be very careful about using my Order numbers consistently- I’m already thinking about how to fit this into existing documentation, like my SDR.

Conclusion

This doesn’t just impact Single Page Apps- even a traditional Page Load Rule implementation sometimes needs to make sure one rule fires after another, perhaps to overwrite the variables of another, or to check a variable another rule set (maybe I’m hard coding s.channel in one rule, and based on that value, want to fire another rule). I can even think of cases where this would be helpful for third party tags. This is a really powerful feature that should give a lot more control and flexibility to your tag management implementation.

Let me know if you think of new advantages, use cases, or potential “gotchas” for this feature!